ACCOMMODATIONS
- Layout: 2 Cabin, 2 Head Center Cockpit Sloop
- The interior of the Endeavour 40 is built up of wood. First, a framework of floor timbers is constructed and placed in the bilge and heavily bonded in place with woven roving. A plywood sole is glued and screwed on top of these floor timbers and bonded to the hull all around its periphery with woven roving.
- All timbers and plywood are saturated with polyester resin before assembly to seal all exposed wood. All bulkheads are bonded to the hull with two layers of woven roving on both sides.
- The interior is finished with varnished teak with soft white overheads. The cabin sole is teak parquet flooring, bonded in place with a waterproof adhesive.
- The interior layout is typical with a V-berth forward, the head (to starboard) and lockers (to port) which divide it from the main salon area which has a fold-up dining table with port and starboard settees. Aft and to starboard is a nav station with the electrical panel and to port is the galley with refrigeration, a gimbaled 3-burner gas stove with oven.
- The engine area is insulated and can be accessed via the starboard hallway or underneath stairs. The private owner’s stateroom aft has a queen size berth, hanging lockers, chest of drawers, and a private head with shower. Mattress replaced with memory foam in 2021.
- There are 14 opening ports (Beckson) and 4 large Atkins-Hoyle deck hatches (strong drop forged aluminum with 3/4″ Lexan), one each over the v-berth and aft cabin and 2 over the salon area.
ELECTRONICS
- Autopilot – 4/2022
- Radar
- AIS Receive
- Plotter
- Wind
- Speed
- Depth
- GPS
- VHF
ELECTRICAL
- Shore power and battery charger
- LiFePo Batteries, 200A x2 – 10/2023 – 4/2022
- AGM battery 200 A – 11/2023
- Solar Panels, Victron MPPT and DC-DC Chargers – 5/2023
- 2KW Inverter System – 9/2023
- LED Lighting for interior, headlights, cockpit light, stern lighting,
SAILS & RIGGING
- Main & jib, estimated within last 5 years. In need of minor stitching.
- Roller furling jib estimated within last 5 years.
- Sail bag and lazy jacks – 6/2023
DECK & HULL
- Last Bottom job 09/23 – Pettit Trinidad 2 Coats with 3rd coat to waterline
- Bottom cleaned and zincs replaced every 6 months
- Anchor, windlass, and remote.
- Full enclosure bimini, dodger enclosure with single pull zippers – 19/2022
- Canvas hatch cogvers – 10/2022
- Solar: 3 9BB Cell 200 watt 12V solar panels – 4/2022
- Navigation lights, anchor light, steaming and deck light combination
- Lifeline gates
- Fenders and lines
MECHANICAL
- Engine – Perkins 4-108 (50hp) auxiliary
- No hour meter
- Engine oil changed 10/2023
- Transmission fluid changed 10/2023
- Impeller changed 10/2023
- Throttle control handle – 9/2022
- The diesel is fitted with a mechanical gearbox transmission.
- Dripless shaft seal: The propeller shaft is made of 1-1/4″ stainless steel and exits the hull through a stuffing box. It is supported at the inboard, or engine end, by the shaft coupling, and at the aft end by a cutlass bearing mounted in a stainless steel shaft log bolted to a fiberglass skeg immediately aft of the keel. The skeg is integrally molded with the hull.
- The standard propeller was a 17″ x 17 2-blade prop or an optional 17″ x 16 3-blade prop
- Generator
- Air conditioning – CitiMarine 16k btu and 10k btu – 8/2022
- 30 GPH Watermaker
- 150 gallon water tank, fiberglass, replaced 2023
- 75 gallon water tank, fiberglass, replaced 2023
HISTORY OF VESSEL
The current owners bought Sibelle in 2022 and made significant upgrades over the last 3 years. The fuel and water tanks have been replaced with fiberglass and the fuel system rebuilt. The rudder bearing, rear seal, and cutlass bearing have all been replaced. An extensive maintenance and upgrade log since purchase is available upon request.
Little Yacht Sales is pleased to assist you in the purchase of this vessel. This boat is centrally listed by Murray Yacht Sales. It is offered as a convenience by this broker/dealer to its clients and is not intended to convey direct representation of a particular vessel